View LC87F5864C_4695557.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

83006 / 42706hkim no.a0344-1/23 ver.1.05 LC87F5864C overview the sanyo LC87F5864C is an 8-bit microcomputer that, cent ered around a cpu running at a minimum bus cycle time of 83.3ns, integrates on a single chip a number of hardware features such as 64k-byte flash rom (onboard programmable), 2048-byte ram, sophisticated 16-bit timers/counters (may be divided into 8-bit timers), a 16-bit timer/counter (may be divided into 8-bit timers/counters or 8-bit pwms), four 8-bit timers with a prescaler, a base timer serving as a time-of-day clock, a high-speed cl ock counter, a synchronous sio interface (with automatic block transmission/reception capabilities), an asynchronous/synchronous sio interface , a uart interface (full duplex ), an 8-bit 11-channel ad converter, two 12-bit pwm channels, a system clock frequency divider, rom correction function, and a 23-source 10-vector interrupt feature. features ? flash rom ? capable of on-board-programing with wide range, 3.0 to 5.5v, of voltage source. ? block-erasable in 128 byte units ? 65536 8-bits (LC87F5864C) ? ram ? 2048 9 bits (LC87F5864C) ? minimum bus cycle ? 83.3ns (12mhz) v dd =3.0 to 5.5v ? 125ns (8mhz) v dd =2.5 to 5.5v ? 500ns (2mhz) v dd =2.2 to 5.5v note: the bus cycle time here refers to the rom read speed. ? minimum instruction cycle time ? 250ns (12mhz) v dd =3.0 to 5.5v ? 375ns (8mhz) v dd =2.5 to 5.5v ? 1.5 s (2mhz) v dd =2.2 to 5.5v ordering number : ena0344 cmos ic from 64k byte, ram 2048 byte on-chip 8-bit 1-chip microcontroller *this product incorporates technology licensed from silicon storage technology inc any and all sanyo semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. consult with your sanyo semiconductor representative nearest you before usingany sanyo semiconductor products described or contained herein in such applications. sanyo semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated val ues (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all sanyo semiconductor products described or contained herein.
LC87F5864C no.a0344-2/23 ? ports ? normal withstand voltage i/o ports ports whose i/o direction can be designated in 1-bit units 46 (p1n, p2n, p70 to p73, p80 to p86, pbn, pcn, pwm2, pwm3, xt2) ports whose i/o direction can be designated in 4-bit units 8 (p0n) ? normal withstand voltage input port 1 (xt1) ? dedicated oscillator ports 2 (cf1, cf2) ? reset pins 1 (res) ? power pins 6 (v ss 1 to 3, v dd 1 to 3) ? timers ? timer 0 : 16-bit timer/counter with a capture register mode 0 : 8-bit timer with an 8-bit programmabl e prescaler (with an 8-bit capture register) 2-channels mode 1 : 8-bit timer with an 8-bit programmable prescal er (with an 8-bit capture register) + 8-bit counter (with an 8-bit capture register) mode 2 : 16-bit timer with an 8-bit programma ble prescaler (with a 16-bit capture register) mode 3 : 16-bit counter (with a 16-bit capture register) ? timer 1 : 16-bit timer/counter that supports pwm/toggle outputs mode 0 : 8-bit timer with an 8-bit prescaler (with toggle outputs) + 8-bit timer/counter with an 8-bit prescaler (with toggle outputs) mode 1 : 8-bit pwm with an 8-bit prescaler 2-channels mode 2 : 16-bit timer/counter with an 8-bit prescaler (with toggle outputs) (toggle outputs also possible from the lower-order 8-bits) mode 3 : 16-bit timer with an 8-bit prescaler (with toggle outputs) (the lower-order 8 bits can be used as pwm) ? timer 4 : 8-bit timer with a 6-bit prescaler ? timer 5 : 8-bit timer with a 6-bit prescaler ? timer 6 : 8-bit timer with a 6-bit prescaler (with toggle outputs) ? timer 7 : 8-bit timer with a 6-bit prescaler (with toggle outputs) ? base timer 1) the clock is selectable from the subclock (32.768khz crystal oscillation), system clock, and timer 0 prescaler output. 2) interrupts programmable in 5 different time schemes ? high-speed clock counter 1) can count clocks with a maximum clock rate of 20mhz (at a main clock of 10mhz) 2) can generate output real-time ? sio ? sio0 : 8-bit synchronous serial interface 1) lsb first/msb first mode selectable 2) built-in 8-bit baudrate generator (maximum transfer clock cycle=4/3 tcyc) 3) automatic continuous data transmission (1 to 256 bits, specifiable in 1 bit units, suspension and resumption of data transmission possible in 1 byte units) ? sio1 : 8-bit asynch ronous/synchronous serial interface mode 0 : synchronous 8-bit serial i/o (2- or 3-wire configuration, 2 to 512 tcyc transfer clocks) mode 1 : asynchronous serial i/o (half-duplex, 8 data bits, 1 stop bit, 8 to 2048 tcyc baudrates) mode 2 : bus mode 1 (start bit, 8 data bits, 2 to 512 tcyc transfer clocks) mode 3 : bus mode 2 (start detect, 8 data bits, stop detect) ? uart ? full duplex ? 7/8/9 bit data bits selectable ? 1 stop bit (2-bit in continuous data transmission) ? built-in baudrate generator
LC87F5864C no.a0344-3/23 ? ad converter : 8 bits 11 channels ? pwm : multifrequency 12-bit pwm 2-channels ? remote control receiver circuit (sharing pins with p73, int3, and t0in) ? noise rejection function (noise filter time constant selectable from 1 tcyc, 32 tcyc, and 128 tcyc) ? watchdog timer ? external rc watchdog timer ? interrupt and reset signals selectable ? clock output function 1) able to output selected oscillation clock 1/1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64 as system clock. 2) able to output oscillation clock of sub clock. ? interrupts ? 23 sources, 10 vector addresses 1) provides three levels (low (l), high (h), and highest (x)) of multiplex interrupt cont rol. any interrupt requests of the level equal to or lower than the current interrupt are not accepted. 2) when interrupt requests to two or more vector addresses occur at the same time, the interrupt of the highest level takes precedence over the other interrupts. for interrupts of the same level, the interrupt into the smallest vector address takes precedence. no. vector address level interrupt source 1 00003h x or l int0 2 0000bh x or l int1 3 00013h h or l int2/t0l/int4 4 0001bh h or l int3/int5/base timer0/base timer1 5 00023h h or l t0h 6 0002bh h or l t1l/t1h 7 00033h h or l sio0/uart1 receive 8 0003bh h or l sio1/uart1 transmit 9 00043h h or l adc/t6/t7 10 0004bh h or l port 0/t4/t5/pwm2, pwm3 ? priority levels x > h > l ? of interrupts of the same level, the one with the smallest vector address takes precedence. ? subroutine stack levels : 1024 levels (the stack is allocated in ram) ? high-speed multiplication/division instructions ? 16 bits 8 bits (5 tcyc execution time) ? 24 bits 16 bits (12 tcyc execution time) ? 16 bits 8 bits (8 tcyc execution time) ? 24 bits 16 bits (12 tcyc execution time) ? oscillation circuits ? rc oscillation circuit (internal) : for system clock ? cf oscillation circuit : for system clock, with internal rf ? crystal oscillation circuit : for low-sp eed system clock, with internal rf ? system clock divider function ? can run on low current. ? the minimum instruction cycle selectable from 300ns, 600ns, 1.2 s, 2.4 s, 4.8 s, 9.6 s, 19.2 s, 38.4 s, and 76.8 s (at a main clock rate of 10mhz).
LC87F5864C no.a0344-4/23 ? standby function ? halt mode : halts instruction execution while allowing the peripheral circuits to continue operation. 1) oscillation is not halted automatically. 2) canceled by a system reset or occurrence of an interrupt ? hold mode : suspends instruction execution an d the operation of the peripheral circuits. 1) the cf, rc, and crystal oscilla tors automatically stop operation. 2) there are three ways of resetting the hold mode. (1) setting the reset pin to the low level (2) setting at least one of the int0, int1, int2 , int4, and int5 pins to the specified level (3) having an interrupt source established at port 0 ? x'tal hold mode : suspends instruction execution and the operation of the peripheral circuits except the base timer. 1) the cf and rc oscillators automatically stop operation. 2) the state of crystal oscillation established wh en the x'tal hold mode is entered is retained. 3) there are four ways of resetting the x'tal hold mode. (1) setting the reset pin to the low level (2) setting at least one of the int0, int1, int2 , int4, and int5 pins to the specified level (3) having an interrupt source established at port 0 (4) having an interrupt source established in the base timer circuit ? package form ? vqfn64 (10 10): lead-free type ? tqfp64j (7 7): lead-free type ? development tools ? evaluation chip : lc87ev690 ? emulator : eva62s + ecb876600d + sub875800 ? programming boards ? w87f58256vq (for vqfn64 (10 10) package) ? w87f58256tq7 (for tqfp64j (7 7) packages)
LC87F5864C no.a0344-5/23 package dimensions unit : mm 3323 package dimensions unit : mm 3289 7.0 9.0 7.0 9.0 0.125 0.5 0.16 0.4 (0.5) (1.0) 1.2max 0.1 1 16 33 48 17 64 32 49 sanyo : tqfp64j(7x7) 10.2 8.0 typ 8.0 typ 10.2 0.3 0.3 depth:0.03 min 0 . 2 10.0 (0.8) 0.85max 10.0 (1.25) 0.5 side view side view bottom view top view 0.5 0.5 0.2 do not connect 116 11 32 33 48 49 64 sanyo : vqfn64(10x10)
LC87F5864C no.a0344-6/23 pin assignments sanyo: vqfn64 (10 10) ?lead-free type? top view p06/t6o p07/t7o p20/utx/int4/t1in p21/urx/int4/t1in p22/int4/t1in p23/int4/t1in p24/int5/t1in p25/int5/t1in p26/int5/t1in p27/int5/t1in pb7 pb6 pb5 pb4 pb3 pb2 pb1 pb0 v ss 3 v dd 3 pc7 pc6 pc5 pc4 pc3 pc2 pc1 pc0 p86/an6 p85/an5 p84/an4 p83/an3 p05/cko p04 p03 p02 p01 p00 v ss 2 v dd 2 pwm3 pwm2 p17/t1pwmh/buz p16/t1pwml p15/sck1 p14/si1/sb1 p13/so1 p12/sck0 p11/si0/sb0 p10/so0 p82/an2 p81/an1 p80/an0 v dd 1 cf2 cf1 v ss 1 xt2/an11 xt1/an10 res p73/int3/t0in p72/int2/t0in p71/int1/t0hcp/an9 p70/int0/t0lcp/an8 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 LC87F5864C
LC87F5864C no.a0344-7/23 sanyo: tqfp64j (7 7) ?lead-free type? LC87F5864C top view p83/an3 p84/an4 p85/an5 p86/an6 pc0 pc1 pc2 pc3 pc4 pc5 pc6 pc7 v dd 3 v ss 3 pb0 pb1 pb2 pb3 pb4 pb5 pb6 pb7 p27/int5/t1in p26/int5/t1in p25/int5/t1in p24/int5/t1in p23/int4/t1in p22/int4/t1in p21/urx/int4/t1in p20/utx/int4/t1in p07/t7o p06/t6o p70/int0/t0lcp/an8 p71/int1/t0hcp/an9 p72/int2/t0in p73/int3/t0in res xt1/an10 xt2/an11 v ss 1 cf1 cf2 v dd 1 p80/an0 p81/an1 p82/an2 p10/so0 p11/si0/sb0 p12/sck0 p13/so1 p14/si1/sb1 p15/sck1 p16/t1pwml p17/t1pwmh/buz pwm2 pwm3 v dd 2 v ss 2 p00 p01 p02 p03 p04 p05/cko 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 4 8 47 4 6 4 5 44 4 3 42 4 0 39 38 3 7 36 35 3 4 33 12 3 4 5 6 7 8 9 10 11 12 13 14 15 16 41
LC87F5864C no.a0344-8/23 system block diagram interrupt control standby control ir pla clock generator cf rc x?tal bus interface port 0 port 1 sio0 sio1 timer 0 timer 1 timer 4 timer 5 port 2 port 7 port 8 adc alu flash rom pc acc b register c register psw rar ram stack pointer watchdog timer pwm2/3 uart base timer timer 6 int0 to int5 noise filter timer 7 port b port c rom correct
LC87F5864C no.a0344-9/23 pin description pin name i/o description option v ss 1, v ss 2 v ss 3 - - power supply pin no v dd 1, v dd 2 v dd 3 - + power supply pin no port 0 p00 to p07 i/o ? 8-bit i/o port ? i/o specifiable in 4-bit units ? pull-up resistor can be turned on and off in 4-bit units ? hold release input ? port 0 interrupt input ? shared pins p05 : clock output (system clock / can selected from sub clock) p06 : timer 6 toggle output p07 : timer 7 toggle output yes port 1 p10 to p17 i/o ? 8-bit i/o port ? i/o specifiable in 1-bit units ? pull-up resistor can be turned on and off in 1-bit units ? pin functions p10 : sio0 data output p11 : sio0 data input/bus i/o p12 : sio0 clock i/o p13 : sio1 data output p14 : sio1 data input/bus i/o p15 : sio1 clock i/o p16 : timer 1 pwml output p17 : timer 1 pwmh output/beeper output yes port 2 ? 8-bit i/o port ? i/o specifiable in 1-bit units ? pull-up resistors can be turned on and off in 1-bit units ? pin functions p20 : uart transmit p21 : uart receive p20 to p23 : int4 input/hold reset input/timer 1 event input/timer 0l capture input /timer 0h capture input p24 to p27 : int5 input/hold reset input/timer 1 event input/timer 0l capture input /timer 0h capture input ? interrupt acknowledge type rising falling rising/ falling h level l level int4 enable enable enable disable disable int5 enable enable enable disable disable p20 to p27 i/o yes port 7 ? 4-bit i/o port ? i/o specifiable in 1-bit units ? pull-up resistor can be turned on and off in 1-bit units ? shared pins p70 : int0 input/hold reset input/timer 0l capture input/watchdog timer output p71 : int1 input/hold reset input/timer 0h capture input p72 : int2 input/hold reset input/timer 0 event input/timer 0l capture input/ high speed clock counter input p73 : int3 input (with noise filter)/timer 0 event input/timer 0h capture input ad converter input port: an8 (p70), an9 (p71) ? interrupt acknowledge type rising falling rising/ falling h level l level int0 enable enable disable enable enable int1 enable enable disable enable enable int2 enable enable enable disable disable int3 enable enable enable disable disable p70 to p73 i/o no continued on next page.
LC87F5864C no.a0344-10/23 continued from preceding page. pin name i/o description option port 8 p80 to p86 i/o ? 7-bit i/o port ? i/o specifiable in 1-bit units ? shared pins ad converter input port : an0 (p80) to an6 (p86) no pwm2 pwm3 i/o ? pwm2 and pwm3 output ports ? general-purpose i/o available no port b pb0 to pb7 i/o ? 8-bit i/o port ? i/o specifiable in 1-bit units ? pull-up resistor can be turned on and off in 1-bit units yes port c pc0 to pc7 i/o ? 8-bit i/o port ? i/o specifiable in 1-bit units ? pull-up resistor can be turned on and off in 1-bit units yes res input reset pin no xt1 input ? 32.768khz crystal oscillator input pin ? shared pins general-purpose input port ad converter input port : an10 must be connected to v dd 1 if not to be used. no xt2 i/o ? 32.768khz crystal oscillator output pin ? shared pins general-purpose i/o port ad converter input port : an11 must be set for oscillation and kept open if not to be used. no cf1 input ceramic resonator input pin no cf2 output ceramic resonator output pin no
LC87F5864C no.a0344-11/23 port output types the table below lists the types of port outputs and the presence/absence of a pull-up resistor. data can be read into any input port even if it is in the output mode. port name option selected in units of option type output type pull-up resistor 1 cmos programmable (note 1) p00 to p07 1 bit 2 nch-open drain no 1 cmos programmable p10 to p17 1 bit 2 nch-open drain programmable 1 cmos programmable p20 to p27 1 bit 2 nch-open drain programmable p70 - no nch-open drain programmable p71 to p73 - no cmos programmable p80 to p86 - no nch-open drain no pwm2, pwm3 - no cmos no 1 cmos programmable pb0 to pb7 1 bit 2 nch-open drain programmable 1 cmos programmable pc0 to pc7 1 bit 2 nch-open drain programmable xt1 - no input for 32.768khz crystal oscillator (input only) no xt2 - no output for 32.768khz crystal oscillator (nch-open drain when in general-purpose output mode) no note 1 : programmable pull-up resistors for port 0 are controlled in 4-bit units (p00 to 03, p04 to 07). *1 : connect the ic as shown below to minimize the noise input to the v dd 1 pin. be sure to electrically short the v ss 1, v ss 2, and v ss 3 pins. *2 : the internal memory is sustained by v dd 1. if none of v dd 2 and v dd 3 are backed up, the high level output at the ports are unstable in the hold backup mode, allowing through current to flow into the input buffer and thus shortening the backup time. make sure that the port outputs are held at the low level in the hold backup mode. power supply lsi v dd 1 for backup *2 v dd 2 v dd 3 v ss 3 v ss 2 v ss 1
LC87F5864C no.a0344-12/23 absolute maximum ratings at ta = 25c, v ss 1 = v ss 2 = v ss 3 = 0v specification parameter symbol pin/remarks conditions v dd [v] min typ max unit maximum supply voltage v dd max v dd 1, v dd 2, v dd 3v dd 1=v dd 2=v dd 3 -0.3 +6.5 input voltage v i (1) xt1, cf1 -0.3 v dd +0.3 input/output voltage vio(1) ports 0, 1, 2 ports 7, 8 ports b, c pwm2, pwm3, xt2 -0.3 v dd +0.3 v ioph(1) ports 0, 1, 2 ports b, c cmos output select per 1 applicable pin -10 ioph(2) pwm2, pwm3 per 1 applicable pin -20 peak output current ioph(3) p71 to p73 per 1 applicable pin -5 iomh(1) ports 0, 1, 2 ports b, c cmos output select per 1 applicable pin -7.5 iomh(2) pwm2, pwm3 per 1 applicable pin -15 mean output current (note 1-1) iomh(3) p71 to p73 per 1 applicable pin -3 ioah(1) p71 to p73 total of all applicable pins -10 ioah(2) port 1 pwm2, pwm3 total of all applicable pins -25 ioah(3) ports 0, 2 total of all applicable pins -25 ioah(4) ports 0, 1, 2 pwm2, pwm3 total of all applicable pins -45 ioah(5) port b total of all applicable pins -25 ioah(6) port c total of all applicable pins -25 high level output current total output current ioah(7) ports b, c total of all applicable pins -45 iopl(1) p02 to p07 ports 1, 2 ports b, c pwm2, pwm3 per 1 applicable pin 20 iopl(2) p00, p01 per 1 applicable pin 30 peak output current iopl(3) ports 7, 8, xt2 per 1 applicable pin 10 ioml(1) p02 to p07 ports 1, 2 ports b, c pwm2, pwm3 per 1 applicable pin 15 ioml(2) p00, p01 per 1 applicable pin 20 mean output current (note 1-1) ioml(3) ports 7, 8, xt2 per 1 applicable pin 7.5 ioal(1) port 7 p83 to p86, xt2 total of all applicable pins 15 ioal(2) p80 to p82 total of all applicable pins 15 ioal(3) ports 7, 8, xt2 total of all applicable pins 20 ioal(4) port 1 pwm2, pwm3 total of all applicable pins 45 ioal(5) ports 0, 2 total of all applicable pins 45 ioal(6) ports 0, 1, 2 pwm2, pwm3 total of all applicable pins 80 ioal(7) port b total of all applicable pins 45 ioal(8) port c total of all applicable pins 45 low level output current total output current ioal(9) ports b, c total of all applicable pins 80 ma vqfn64(10 10) 190 power dissipation pdmax tqfp64j(7 7) ta=-20 to +70 c 188 mw operating ambient temperature topr -20 70 storage ambient temperature tstg -55 125 c note 1-1 : the mean output current is a mean value measured over 100ms.
LC87F5864C no.a0344-13/23 allowable operating conditions at ta = -20c to +70c, v ss 1 = v ss 2 = v ss 3 = 0v specification parameter symbol pin/remarks conditions v dd [v] min typ max unit 0.245 s tcyc 200 s 3.0 5.5 0.367 s tcyc 200 s 2.5 5.5 operating supply voltage (note 2-1) v dd (1) v dd 1=v dd 2=v dd 3 1.47 s tcyc 200 s 2.2 5.5 memory sustaining supply voltage vhd v dd 1=v dd 2=v dd 3 ram and register contents sustained in hold mode. 2.0 5.5 v ih (1) ports 1, 2 p71 to p73 p70 port input /interrupt side 2.2 to 5.5 0.3v dd +0.7 v dd v ih (2) ports 0, 8, b, c pwm2, pwm3 2.2 to 5.5 0.3v dd +0.7 v dd v ih (3) port 70 watchdog timer side 2.2 to 5.5 0.9v dd v dd high level input voltage v ih (4) xt1, xt2, cf1, res 2.2 to 5.5 0.75v dd v dd 4.0 to 5.5 v ss 0.1v dd +0.4 v il (1) ports 1, 2 p71 to p73 p70 port input /interrupt side 2.2 to 4.0 v ss 0.2v dd 4.0 to 5.5 v ss 0.15v dd +0.4 v il (2) ports 0, 8, b, c pwm2, pwm3 2.2 to 4.0 v ss 0.2v dd v il (3) port 70 watchdog timer side 2.2 to 5.5 v ss 0.8v dd -1.0 low level input voltage v il (4) xt1, xt2, cf1, res 2.2 to 5.5 v ss 0.25v dd v 3.0 to 5.5 0.245 200 2.5 to 5.5 0.367 200 instruction cycle time (note 2-2) tcyc 2.2 to 5.5 1.47 200 s fmcf(1) cf1, cf2 12mhz ceramic oscillation see fig. 1. 3.0 to 5.5 12 fmcf(2) cf1, cf2 8mhz ceramic oscillation see fig. 1. 2.5 to 5.5 8 fmcf(3) cf1, cf2 4mhz ceramic oscillation see fig. 1. 2.2 to 5.5 4 fmrc internal rc oscillation 2.2 to 5.5 0.3 1.0 2.0 mhz oscillation frequency range (note 2-3) fsx?tal xt1, xt2 32.768khz crystal oscillation see fig. 2. 2.2 to 5.5 32.768 khz note 2-1 : v dd must be held greater than or equal to 3.0v in the flash rom onboard programming mode. note 2-2 : relationship between tcyc and oscillation frequency is 3/fmcf at a division ratio of 1/1 and 6/fmcf at a division ratio of 1/2. note 2-3 : see tables 1 and 2 for the oscillation constants.
LC87F5864C no.a0344-14/23 electrical characteristics at ta = -20c to +70c, v ss 1 = v ss 2 = v ss 3 = 0v specification parameter symbol pins conditions v dd [v] min typ max unit i ih (1) ports 0, 1, 2 ports 7, 8 ports b, c res pwm2, pwm3 output disabled pull-up resistor off v in =v dd (including output tr's off leakage current) 2.2 to 5.5 1 i ih (2) xt1, xt2 for input port specification v in =v dd 2.2 to 5.5 1 high level input current i ih (3) cf1 v in =v dd 2.2 to 5.5 15 i il (1) ports 0, 1, 2 ports 7, 8 ports b, c res pwm2, pwm3 output disabled pull-up resistor off v in =v ss (including output tr's off leakage current) 2.2 to 5.5 -1 i il (2) xt1, xt2 for input port specification v in =v ss 2.2 to 5.5 -1 low level input current i il (3) cf1 v in =v ss 2.2 to 5.5 -15 a v oh (1) i oh =-1ma 4.5 to 5.5 v dd -1 v oh (2) i oh =-0.4ma 3.0 to 5.5 v dd -0.4 v oh (3) ports 0, 1, 2 ports b, c i oh =-0.2ma 2.2 to 5.5 v dd -0.4 v oh (4) i oh =-0.4ma 3.0 to 5.5 v dd -0.4 v oh (5) p71 to p73 i oh =-0.2ma 2.2 to 5.5 v dd -0.4 v oh (6) i oh =-10ma 4.5 to 5.5 v dd -1.5 v oh (7) i oh =-1.6ma 3.0 to 5.5 v dd -0.4 high level output voltage v oh (8) pwm2, pwm3 i oh =-1ma 2.2 to 5.5 v dd -0.4 v ol (1) i ol =10ma 4.5 to 5.5 1.5 v ol (2) i ol =1.6ma 3.0 to 5.5 0.4 v ol (3) ports 0, 1, 2 ports b, c pwm2, pwm3 i ol =1ma 2.2 to 5.5 0.4 v ol (4) i ol =1.6ma 3.0 to 5.5 0.4 v ol (5) ports 7, 8 xt2 i ol =1ma 2.2 to 5.5 0.4 v ol (6) i ol =30ma 4.5 to 5.5 1.5 v ol (7) i ol =5ma 3.0 to 5.5 0.4 low level output voltage v ol (8) p00, p01 i ol =2.5ma 2.2 to 5.5 0.4 v rpu(1) 4.5 to 5.5 15 35 80 pull-up resistance rpu(2) ports 0, 1, 2, 7 ports b, c v oh =0.9v dd 2.2 to 5.5 18 50 150 k ? hysteresis voltage vhys res ports 1, 2, 7 2.2 to 5.5 0.1 v dd v pin capacitance cp all pins for pins other than that under test: v in =v ss f=1mhz ta=25 c 2.2 to 5.5 10 pf
LC87F5864C no.a0344-15/23 serial input/output characteristics at ta = -20c to +70c, v ss 1 = v ss 2 = v ss 3 = 0v 1. sio0 serial i/o characteristics (note 4-1-1) specification parameter symbol pin/remarks conditions v dd [v] min typ max unit frequency tsck(1) 2 low level pulse width tsckl(1) 1 tsckh(1) see fig. 6. 1 input clock high level pulse width tsckha(1) sck0(p12) ? continuous data transmission/reception mode ? see fig. 6. ? (note 4-1-2) 2.2 to 5.5 4 frequency tsck(2) 4/3 tcyc low level pulse width tsckl(2) 1/2 tsckh(2) ? cmos output selected ? see fig. 6. 1/2 tsck serial clock output clock high level pulse width tsckha(2) sck0(p12) ? continuous data transmission/reception mode ? cmos output selected ? see fig. 6. 2.2 to 5.5 tsckh(2) +2tcyc tsckh(2) +(10/3) tcyc tcyc data setup time tsdi(1) 2.2 to 5.5 0.03 serial input data hold time thdi(1) sb0(p11), si0(p11) ? must be specified with respect to rising edge of sioclk. ? see fig. 6. 2.2 to 5.5 0.03 tdd0(1) ? continuous data transmission/reception mode ? (note 4-1-3) 2.2 to 5.5 (1/3)tcyc +0.05 input clock tdd0(2) ? synchronous 8-bit mode ? (note 4-1-3) 2.2 to 5.5 1tcyc +0.05 serial output output clock output delay time tdd0(3) so0(p10), sb0(p11) (note 4-1-3) 2.2 to 5.5 (1/3)tcyc +0.15 s note 4-1-1: these specifications are theoretical values. add margin depending on its use. note 4-1-2: to use serial-clock-input in continuous trans / rec mode, a time from si0run being set when serial clock is "h" to the first negative edge of the serial clock must be longer than tsckha. note 4-1-3: must be specified with respect to falling edge of sioclk. must be specified as the time to the beginning of output state change in open drain output mode. see fig. 6.
LC87F5864C no.a0344-16/23 2. sio1 serial i/o characteristics (note 4-2-1) specification parameter symbol pin/remarks conditions v dd [v] min typ max unit frequency tsck(3) 2 low level pulse width tsckl(3) 1 input clock high level pulse width tsckh(3) sck1(p15) see fig. 6. 2.2 to 5.5 1 frequency tsck(4) 2 tcyc low level pulse width tsckl(4) 1/2 serial clock output clock high level pulse width tsckh(4) sck1(p15) ? cmos output selected ? see fig. 6. 2.2 to 5.5 1/2 tsck data setup time tsdi(2) 2.2 to 5.5 0.03 serial input data hold time thdi(2) sb1(p14), si1(p14) ? must be specified with respect to rising edge of sioclk. ? see fig. 6. 2.2 to 5.5 0.03 serial output output delay time tdd0(4) so1(p13), sb1(p14) ? must be specified with respect to falling edge of sioclk. ? must be specified as the time to the beginning of output state change in open drain output mode. ? see fig. 6. 2.2 to 5.5 (1/3)tcyc +0.05 s note 4-2-1: these specifications are theoretical values. add margin depending on its use.
LC87F5864C no.a0344-17/23 pulse input conditions at ta = -20c to +70c, v ss 1 = v ss 2 = v ss 3 = 0v specification parameter symbol pins/remarks conditions v dd [v] min typ max unit tpih(1) tpil(1) int0(p70), int1(p71), int2(p72), int4(p20 to p23), int5(p24 to p27) ? interrupt source flag can be set. ? event inputs for timer 0 or 1 are enabled. 2.2 to 5.5 1 tpih(2) tpil(2) int3(p73) when noise filter time constant is 1/1 ? interrupt source flag can be set. ? event inputs for timer 0 are enabled. 2.2 to 5.5 2 tpih(3) tpil(3) int3(p73) when noise filter time constant is 1/32 ? interrupt source flag can be set. ? event inputs for timer 0 are enabled. 2.2 to 5.5 64 tpih(4) tpil(4) int3(p73) when noise filter time constant is 1/128 ? interrupt source flag can be set. ? event inputs for timer 0 are enabled. 2.2 to 5.5 256 tcyc high/low level pulse width tpil(5) res resetting is enabled. 2.2 to 5.5 200 s ad converter characteristics at ta = -20c to +70c, v ss 1 = v ss 2 = v ss 3 = 0v specification parameter symbol pins/remarks conditions v dd [v] min typ max unit resolution n 3.0 to 5.5 8 bit absolute accuracy et (note 6-1) 3.0 to 5.5 1.5 lsb 4.5 to 5.5 15.68 (tcyc= 0.49s) 97.92 (tcyc= 3.06s) ad conversion time = 32 tcyc (when adcr2 = 0) (note 6-2) 3.0 to 5.5 23.52 (tcyc= 0.735s) 97.92 (tcyc= 3.06s) 4.5 to 5.5 18.82 (tcyc= 0.294s) 97.92 (tcyc= 1.53s) conversion time tcad ad conversion time = 64 tcyc (when adcr2 = 1) (note 6-2) 3.0 to 5.5 47.04 (tcyc= 0.735s) 97.92 (tcyc= 1.53s) s analog input voltage range vain 3.0 to 5.5 v ss v dd v iainh vain=v dd 3.0 to 5.5 1 analog port input current iainl an0(p80) to an6(p86), an8(p70), an9(p71), an10(xt1), an11(xt2) vain=v ss 3.0 to 5.5 -1 a note 6-1 : the quantization error ( 1/2lsb) is excluded from th e absolute accuracy value. note 6-2 : the conversion time refers to the interval from th e time the instruction for starting the converter is issued till the time the complete digital value corresponding to the analog input value is loaded in the required register.
LC87F5864C no.a0344-18/23 consumption current characteristics at ta = -20c to +70c, v ss 1 = v ss 2 = v ss 3 = 0v specification parameter symbol pin/ remarks conditions v dd [v] min typ max unit iddop(1) 4.5 to 5.5 8.7 22 iddop(2) ? fmcf=12mhz ceramic oscillation mode ? fmx?tal=32.768khz crystal oscillation mode ? system clock set to 12mhz side ? internal rc oscillation stopped. ? 1/1 frequency division ratio 3.0 to 3.6 5 12.5 iddop(3) 4.5 to 5.5 6.6 16.5 iddop(4) 3.0 to 3.6 3.8 9.6 iddop(5) ? fmcf=8mhz ceramic oscillation mode ? fmx?tal=32.768khz crystal oscillation mode ? system clock set to 8 mhz side ? internal rc oscillation stopped. ? 1/1 frequency division ratio 2.5 to 3.0 2.5 7.4 iddop(6) 4.5 to 5.5 2.5 6.3 iddop(7) 3.0 to 3.6 1.4 3.5 iddop(8) ? fmcf=4mhz ceramic oscillation mode ? fmx?tal=32.768khz crystal oscillation mode ? system clock set to 4 mhz side ? internal rc oscillation stopped. ? 1/2 frequency division ratio 2.2 to 3.0 0.9 2.7 iddop(9) 4.5 to 5.5 0.75 3.1 iddop(10) 3.0 to 3.6 0.4 1.7 iddop(11) ? fmcf=0hz (oscillation stopped) ? fmx?tal=32.768khz crystal oscillation mode ? system clock set to internal rc oscillation ? 1/2 frequency division ratio 2.2 to 3.0 0.28 1.35 ma iddop(12) 4.5 to 5.5 35 115 iddop(13) 3.0 to 3.6 18 65 normal mode consumption current (note 7-1) iddop(14) ? fmcf=0hz (oscillation stopped) ? fmx?tal=32.768khz crystal oscillation mode ? system clock set to 32.768khz side ? internal rc oscillation stopped. ? 1/2 frequency division ratio 2.2 to 3.0 12 46 a iddhalt(1) 4.5 to 5.5 3.6 8.2 iddhalt(2) ? halt mode ? fmcf=12mhz ceramic oscillation mode ? fmx?tal=32.768khz crystal oscillation mode ? system clock set to 12mhz side ? internal rc oscillation stopped. ? frequency variable rc oscillation stopped. ? 1/1 frequency division ratio 3.0 to 3.6 2 4.6 iddhalt(3) 4.5 to 5.5 2.6 5.9 iddhalt(4) 3.0 to 3.6 1.4 3.3 iddhalt(5) ? halt mode ? fmcf=8mhz ceramic oscillation mode ? fmx?tal=32.768khz crystal oscillation mode ? system clock set to 8mhz side ? internal rc oscillation stopped. ? frequency variable rc oscillation stopped. ? 1/1 frequency division ratio 2.5 to 3.0 1 2.5 iddhalt(6) 4.5 to 5.5 1.15 2.65 iddhalt(7) 3.0 to 3.6 0.6 1.5 iddhalt(8) ? halt mode ? fmcf=4mhz ceramic oscillation mode ? fmx?tal=32.768khz crystal oscillation mode ? system clock set to 4mhz side ? internal rc oscillation stopped. ? frequency variable rc oscillation stopped. ? 1/2 frequency division ratio 2.2 to 3.0 0.4 1.1 iddhalt(9) 4.5 to 5.5 0.37 1.3 iddhalt(10) 3.0 to 3.6 0.2 0.75 halt mode consumption current (note 7-1) iddhalt(11) v dd 1 =v dd 2 =v dd 3 ? halt mode ? fmcf=0hz (oscillation stopped) ? fmx?tal=32.768khz crystal oscillation mode ? system clock set to internal rc oscillation ? frequency variable rc oscillation stopped. ? 1/2 frequency division ratio 2.2 to 3.0 0.13 0.54 ma note 7-1 : the consumption current value includes none of the cu rrents that flow into the output tr and internal pull-up resistors. continued on next page.
LC87F5864C no.a0344-19/23 continued from preceding page. specification parameter symbol pin/ remarks conditions v dd [v] min typ max unit iddhalt(12) 4.5 to 5.5 18.5 68 iddhalt(13) 3.0 to 3.6 10 38 halt mode consumption current (note 7-1) iddhalt(14) v dd 1 =v dd 2 =v dd 3 ? halt mode ? fmcf=0hz (oscillation stopped) ? fmx?tal=32.768khz crystal oscillation mode ? system clock set to 32.768khz side ? internal rc oscillation stopped. ? frequency variable rc oscillation stopped. ? 1/2 frequency division ratio 2.2 to 3.0 6.5 26 iddhold(1) 4.5 to 5.5 0.05 20 iddhold(2) 3.0 to 3.6 0.03 12 hold mode consumption current iddhold(3) ? hold mode ? cf1=v dd or open (external clock mode) 2.2 to 3.0 0.02 8 iddhold(4) 4.5 to 5.5 16 58 iddhold(5) 3.0 to 3.6 8.5 32 timer hold mode consumption current iddhold(6) v dd 1 ? timer hold mode ? cf1=v dd or open (external clock mode) ? fmx?tal=32.768khz crystal oscillation mode 2.2 to 3.0 5 20 a note 7-1 : the consumption current value includes none of the cu rrents that flow into the output tr and internal pull-up resistors. f-rom programming characteristics at ta = +10c to +55c, v ss 1 = v ss 2 = v ss 3 = 0v specification parameter symbol pin/ remarks conditions v dd [v] min typ max unit onboard programming current iddfw(1) v dd 1 ? 128-byte programming ? erasing current included 3.0 to 5.5 25 40 ma programming time tfw(1) ? 128-byte programming ? erasing current included ? time for setting up 128-byte data is excluded. 3.0 to 5.5 22.5 45 ms uart (full duplex) op erating conditions at ta = -20c to +70c, v ss 1 = v ss 2 = v ss 3 = 0v specification parameter symbol pin/remarks conditions v dd [v] min typ max unit transfer rate ubr p20, p21 2.2 to 5.5 16/3 8192/3 tcyc data length: 7, 8, and 9 bits (lsb first) stop bits: 1 bit (2-bit in continuous data transmission) parity bits: none example of continuous 8-bit data transmission mode processing (first transmit data=55h) example of continuous 8-bit da ta reception mode processing (first receive data=55h) transmit data (lsb first) start of transmission end of transmission ubr start bit stop bit stop bit end of reception ubr receive data (lsb first) start of rece p tion start bit
LC87F5864C no.a0344-20/23 characteristics of a sample main system clock oscillation circuit given below are the characteristics of a sample main syst em clock oscillation circuit that are measured using a sanyo-designated oscillation characteristics evaluation board and external components with circuit constant values with which the oscillator vendor confirmed normal and stable oscillation. table 1 characteristics of a sample main system clock oscillator circuit with a ceramic oscillator circuit constant oscillation stabilization time nominal frequency vendor name oscillator name c1 [pf] c2 [pf] rf1 [ ? ] rd1 [ ? ] operating voltage range [v] typ [ms] max [ms] remarks 12mhz murata cstce12m0g52-r0 (10) (10) open 470 2.8 to 5.5 0.05 0.15 internal c1, c2 cstce8m00g52-r0 (10) (10) open 2.2k 2.7 to 5.5 0.05 0.15 8mhz murata cstls8m00g53-b0 (15) (15) open 680 2.5 to 5.5 0.05 0.15 internal c1, c2 cstcr4m00g53-r0 (15) (15) open 3.3k 2.2 to 5.5 0.05 0.15 4mhz murata cstls4m00g53-b0 (15) (15) open 3.3k 2.2 to 5.5 0.05 0.15 internal c1, c2 the oscillation stabilization time refers to the time interval th at is required for the oscillation to get stabilized after v dd goes above the operating voltage lower limit (see figure 4). characteristics of a sample subs ystem clock oscillator circuit given below are the characteristics of a sample subsystem clock oscillation circuit that are measured using a sanyo- designated oscillation characteristics evaluation board and exte rnal components with circuit constant values with which the oscillator vendor confirmed normal and stable oscillation. table 2 characteristics of a sample subsystem clock oscillator circuit with a crystal oscillator circuit constant oscillation stabilization time nominal frequency vendor name oscillator name c3 [pf] c4 [pf] rf2 [ ? ] rd2 [ ? ] operating voltage range [v] typ [s] max [s] remarks 32.768khz seiko epson mc-306 18 18 open 510k 2.2 to 5.5 1.0 3.0 applicable cl value =12.5pf the oscillation stabilization time refers to the time interval th at is required for the oscillation to get stabilized after the instruction for starting the subclock oscillation circuit is ex ecuted and to the time interval that is required for the oscillation to get stabilized after the hold mode is reset (see figure 4). note : the components that are involved in oscillation should be placed as close to the ic and to one another as possible because they are vulnerable to the influences of the circuit pattern. figure 1 cf oscillator circuit figure 2 xt oscillator circuit figure 3 ac timing measurement point 0.5v dd c3 rd2 c4 x?tal xt2 xt1 rf c1 c2 cf cf2 cf1 rd1 rf
LC87F5864C no.a0344-21/23 reset time and oscillation stabilization time hold reset signal and oscillation stabilization time figure 4 oscillation stabilization times power suppl y res internal rc oscillation cf1, cf2 xt1, xt2 operating mode reset time tmscf tmsx?tal unpredictable reset instruction execution v dd operating v dd lower limit 0v internal rc oscillation cf1, cf2 xt1, xt2 state hold reset signal hold reset signal absent hold reset signal valid tmscf tmsx?tal hold halt
LC87F5864C no.a0344-22/23 figure 5 reset circuit figure 6 serial i/o output waveforms figure 7 pulse input timing signal waveform c res v dd r res res note : determine the value of c res and r res so that the reset signal is present for a period of 200 s after the supply voltage goes beyond the lower limit of the ic?s operating voltage. tpil tpih data ram transfer period (sio0 only) data ram transfer period (sio0 only) di0 di7 di2 di3 di4 di5 di6 di8 do0 do7 do2 do3 do4 do5 do6 do8 di1 do1 sioclk : datain : dataout : dataout : datain : sioclk : dataout : datain : sioclk : tsck tsckl tsckh thdi tsdi tddo tsckl tsckha thdi tsdi tddo
LC87F5864C no.a0344-23/23 ps specifications of any and all sanyo semiconductor pr oducts described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. to verify s ymptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. sanyo semiconductor co., ltd. strives to supply high- quality high-reliability products. however, any and all semiconductor products fail with some probabi lity. it is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property . when designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. in the event that any or all sanyo semiconductor produc ts (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording , or any information storage or retrieval system, or otherwise, without the prior written permission of sanyo semiconductor co., ltd. any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. when designing equipment, refer to the "delivery specification" for the sanyo semiconductor product that you intend to use. information (including circuit diagrams and circui t parameters) herein is for example only; it is not guaranteed for volume production. sanyo semicondu ctor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. this catalog provides i nformation as of april, 2006. specificati ons and information her ein are subject to change without notice.

▲Up To Search▲

Price & Availability of LC87F5864C

	To Download LC87F5864C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .